|
Please note that this product is no longer available from HTC |
Please note that this product is no longer available from HTC |
|
500 grm tubs & 300ml cartridges
|
3 Kg
|
|
Buy Autostic On-Line (Credit Card payment)
To order please telephone: Dennis Hanna 0845 678 2971
Payment by credit card
|
||||||||||||||||||||||||||||||||||||||||||||||||||
|
All major credit cards
accepted
|
AUTOSTIC FC™
TECHNICAL DATA
Autostic is a single element industrial adhesive/cement/sealant. This remarkable
product is simple to use and suitable for a wide range of jointing, coating
and sealing applications. It can be applied by spray, cartridge or trowel.
Autostic Product Benefits
* Single component
* Withstands temperatures up to 1100° c
* Non-toxic
* Non-hazardous
* Solvent resistant
* Acid resistant
Autostic FC Product Range
Available in 3 standard grades :-
* Autostic FC4 for use with spray gun or dipping application
* Autostic FC6 for use with brush or spreader
* Autostic FC8 for use with trowel or cartridge gun application
Other viscosities can be produced to customer's own requirements.
Autostic FC Physical Properties
Type silica based ceramic compound
Viscosity FC4 1000 mPas
FC6 1600 mPas
FC8 3000 mPas
Colour light grey
Flashpoint > 100ºc
Shelflife 12 months
Toxicity non toxic
Cured Properties of Autostic
Compressive strength 28.4 N/mm² or MPa (4119 psi)
Tensile Strength 1.7 N/mm² or MPa (247 psi)
Max. tensile stress 7.1 N/mm² or MPa (1030 psi)
Shear strength 3.2 N/mm² or MPa (464 psi)
Shrinkage 1.5%
Density 2.08 g/cc (130 lb/cu.ft)
Hardness VPN 6 (under 1 kg load)
Volume resistivity 2.9 x 10 9 Ohm/cm
Dielectric strength max. sustained value @ 20ºc-400KV/M
Dielectric constant 41.2
Thermal conductivity @ 105ºc 0.65 W/m c (4.5 BTU in/sq ft/hr/F)
Thermal expansion 18.1 x 10- 6 mm/mm/c
Temperature range -180°c + 1100°c
Gap filling avge. FC4 > 0.5mm
FC6 > 4mm
FC8 > 20mm
Certificates
Autostic holds the following certificates:
BS 476 part 4 non combustible material
DIN 4102 Class A1 (building industry) Non destructibility
Directions for use of Autostic
Surfaces to be bonded should be dry, clean and grease free.
Stir well before use to obtain a uniform light grey colour.
Choose a grade of suitable viscosity to fill the gaps completely, apply to
one surface, bring the two surfaces together and clamp the joint.
Autostic curing
Cure will take place at ambient temperatures but it may take up to 48 hours with the thinner grades, depending on the application. Where possible it is recommended that assemblies be heated to speed up cure. An initial temperature of 70º to 80 ºc is ideal. A post cure at higher temperatures can sometimes improve the properties.
Autostic Packaging
Autostic is available in 500gm and 3kilo containers. FC8 is also available in 500gm cartridge form.
Autostic Storage
Store material in original containers only. A shelf life of 1 year can be expected if stored in conditions of between +5 and+25ºc
Autostic Specifications
The properties listed in this data sheet are typical and should not be used as a basis of preparing specifications.
Note
No liability is accepted for any injury, loss or damage arising directly or indirectly from use of the company's products or from the use of information given in our publications, which is intended to serve as a guide only. Customers should satisfy themselves by appropriate trials that the products are suitable for their intended use.
AUTOSTIC FS ™
TECHNICAL DATA SHEET
Autostic FS is a single component inorganic adhesive for bonding metals and
other low absorbant materials which are required to withstand high temperatures.
It is faster curing than Autostic FC and is more appropriate for some bonding
applications, and particularly with less absorbent substrates.
Autostic FS Product Benefits
* single component
* withstands temperatures up to 1100° c
* non toxic
* non hazardous
* solvent resistant
* acid resistant
Autostic FS Physical Properties
Type silica based ceramic compound
Viscosity 2000m.P.a.s.
Colour white
Flashpoint > 100ºc
Shelflife 12 months
Toxicity non toxic
Cured Properties of Autostic
Compressive strength 28.4 N/mm2 or MPa (4119 psi)
Tensile Strength 1.7 N/mm2 or MPa (247 psi)
Max. tensile stress 7.1 N/mm2 or MPa (1030 psi)
Shear strength 3.2 N/mm2 ore MPa (464 psi)
Shrinkage 1.5%
Density 2.08 g/cc (130 lb/cu.ft)
Hardness VPN 6 (under 1 kg load)
Volume resistivity 2.9 x 10 Ohm/cm
Dielectric strength max. sustained value @ 20c-400KV/M
Dielectric constant 41.2
Thermal conductivity @ 105ºc 0.65 W/m c (4.5 BTU in/sq ft/hr/F)
Thermal expansion 18.1 x 10 mm/mm/c
Temperature range -180°c + 1100°c
Gap filling avge. >4mm
Certificates
Autostic holds the following certificates:
BS 476 part 4 non combustible material (Warrington Fire Research Centre)
DIN 4102 Class A1 (building industry) Non destructability
Autostic FS Directions for use
Surfaces to be bonded should be dry,clean and grease free. Depending on the area to be covered the adhesive can either be applied directly with the cartridge gun nozzle or dispensed in patches and then spread with a spatula or similar tool. When bonding non absorbent surfaces the adhesive need only be applied to one surface. Because of the faster setting of FS when bonding large or absorbent substrates it is advisable to apply the adhesive to both surfaces and in some circumstances it may be desirable to use lower viscosity Autostic products[.Refer to manufacturer for further advise]
Autostic curing
Cure will take place at ambient temperatures but it may take up to 12 hours with lower temperatures. Where possible it is recommended that assemblies be heated to speed up cure. An initial temperature of 70 to 80 °c is ideal. A post cure at higher temperatures can sometimes improve the properties.
Autostic FS Storage
Store material in original containers only. A shelf life of 1 year can be expected if stored in conditions of between +5 and+25 °c
Autostic FS Specifications
The properties listed in this data sheet are typical and should not be used as a basis of preparing specifications.
Note
No liability is accepted for any injury, loss or damage arising directly or indirectly from use of the company's products or from the use of information given in our publications, which is intended to serve as a guide only. Customers should satisfy themselves by appropriate trials that the products are suitable for their intended use.